Quick start guide
SE888
Get started
1
Connect the base station and charger
1
2
3
Connect each end of the power adapter to:
• the DC input jack at the bottom of the base station;
• the power socket on the wall.
Connect each end of the line cord to:
• the telephone socket at the bottom of the base station;
• the telephone socket on the wall.
Power
socket
Telephone
socket
Power
socket
Power
adapter
Extra handset
charger
For multi-handset version, connect each end of the power
adapter to:
Telephone
base station
• the DC input jack at the bottom of the extra handset charger.
• the power socket on the wall.
Note Charge the batteries for 8 hours before first use.
Configure your phone
1
2
The batteries are pre-installed in the handset. Pull the battery
tape off from the battery door before charging.
When using your phone for the first time, you see a welcome
message (country dependent).
3
4
Select your country, then press [OK] to confirm.
Set the date and time.
• If the time is in 12-hour format, press * key to select [AM] or
[PM]
.
Charge your phone
Place the handset on the base station to charge the handset.
When the handset is placed correctly on the base station, you hear
a docking sound.
» The handset starts charging.
Note Charge the batteries for 8 hours before first use.
Charge
8 hours
Check the battery level
When the handset is off the base station/charger, the bars
indicate the battery level (full, medium and low).
When the handset is on the base station/charger, the bars
flash until charging completes.
The empty battery icon flashes and you hear an alert tone.
The battery is low and needs recharging.
Charge your mobile phone
1
2
For iPhone users, connect the plug of your USB charging cable
(not supplied) to the USB socket at the bottom of SE888.
For mobile phones with micro USB charging, connect the micro
USB cable plug to the micro USB socket of the mobile phone.
Telephone
base station
Bluetooth
2
Note
Pair SE888 with your mobile phones
Make sure the Bluetooth function of the mobile phones
is activated and in searching status.Then you can do the
pairing in this way:
• When the Bluetooth device list is full, remove some
mobile phone names before pairing can start.
• If the name of SE888 exists in your mobile phone, you
have to remove it from your mobile phone.Then you
can do the pairing again.
1
2
3
On the base station, press MENU.
Select [Bluetooth] [Find Me]
Place the mobile phone close to the base station, then
press [OK] to confirm.
On the mobile phone, select SE888 and connect.
Enter the PIN code (0000) on the mobile phone if
necessary.
>
.
Tip
For PC pairing and PC phonebook download, install
the PC software ‘ThinkLink’ saved in the cd rom or at
4
5
» When SE888 and the mobile phone are paired,
or
is displayed on the screen of the handset
and base station.
Enjoy
3
Note Make sure that the Line settings are set to
[Home] for land line or [Mobile 1]/[Mobile 2] for
Bluetooth line. For information, see Line settings in the
Phone settings chapter in the user manual.
Call
Quick call from land line
Press
/
on the handset or
on the base station
and dial the phone number.
Dial before you call
Tip If you select [Auto] on the handset, the idle line is
pre-selected for an outgoing call, with [Home] as the
highest priority. Then [Mobile 1] and [Mobile 2]. If
you select [Manual], select an icon among these three
options.
1
2
Dial the phone number on the handset or base station.
Press / to select the land line or Bluetooth line (
) from which you want to make an outgoing call.
Then, you can either:
/
/
3
• press
• press
/
or
on the handset; or
on the base station and select a line
or mobile phone to dial out the call.
Answer a call
Adjust the volume during a call
• When there is an incoming call from the land line, press
Press
/
on the handset or
/
on the base station to
/
on the handset or
on the base station.
change the volume during a call.
• When there is an incoming call from the Bluetooth
line, press
station.
/
on the handset or
on the base
Add a contact in the phonebook
1
2
Press on the handset or base station.
• When there are incoming calls from the land line and
Bluetooth line at the same time, press
handset/base station to select a call, then,
• on the handset, press
• on the base station, press
of the calls.
Select [Option]
>
[Add new], then press [OK] to
/
on the
confirm.
3
4
Enter the name then press [OK] to confirm.
Enter the number, then press [Save] to confirm.
/
; or
or
to pick up one
End a call
• Press
on the handset or
on the base station.
• Place the handset to the base station.
Record an announcement
1
2
Press [Menu]
Select
>
[Announcement], then press [OK] to
confirm.
3
Select [Answer & rec.] or [Answer only], then press
[OK] to confirm.
4
5
6
Select [Record new], then press [OK] to confirm.
Start recording close to the microphone after the beep.
Press [OK] to stop recording.
» You can listen to the newly recorded
announcement on the handset.
Listen to messages recorded on the answering machine
a Switch on/off the answering machine: Press
b Start/Stop listening to the recorded messages: Press
c Adjust the volume: Press
d Delete the current message: Press
.
.
/
.
.
ab cd
Note For more information, see theTelephone answering machine
section in the user manual.
Welcome to Philips
Register your product at www.philips.com/welcome
Need help?
User manual
Refer to the user manual that came with your new phone.
Online help
Reproduction in whole or in part is prohibited
without the written consent of the copyright owner.
Trademarks are the property of Koninklijke Philips
Electronics N.V. or their respective owners.
© 2011 Koninklijke Philips Electronics N.V.
All rights reserved.
0168
QSG_SE888_EN_V1.3
WK11285
|