Pelco Wheelchair BB5HD User Manual

00546

BB5HD Series

Heavy-Duty Spectra^®

Back Box

Installation Manual

C2429M (3/01)

Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com

In North America and Canada: Tel (800) 289-9100 • FAX (800) 289-9150

International Customers: Tel +1(559) 292-1981 • FAX +1(559) 348-1120

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.

2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must

not be installed where exposed to rain and moisture.

3. Only use replacement parts recommended by Pelco.

4. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to

verify the exposed parts have not been connected to line circuitry.

5. The installation method and materials should be capable of supporting four times the weight of the enclosure, pan/tilt, camera and

lens combination.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage

CAUTION:

constituting a risk of electric shock is present

within this unit.

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that there are important

operating and maintenance instructions in the

literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.

Pelco Installation Manual C2429M (3/01)

DESCRIPTION

The Heavy-duty Spectra is perfect for installations where structural integrity and vandalism are a priority. The system features barrel

key locks, heavy-duty construction and a thick acrylic lower dome. The in-ceiling model has a reinforced bracket mounting system for

installation in a fixed ceiling. Pendant models can be mounted to a pole or wall using the IWM Spectra wall mount.

MODELS

BB5HD-F

In-ceiling back box with reinforced bracket-mounting system

BB5HD-PG

BB5HD-PG-E

Indoor, pendant style back box with reinforced sun shroud

Environmental, pendant style back box with heater, fan and reinforced sun shroud

Lower dome models are not interchangeable. Each heavy-duty lower dome is designed for a specific back box model. Install the

correct lower dome to the right back box. See the following chart.

Back Box Model

BB5HD-F

Lower Dome Model

LD5HDF-1

Lower Dome with Cage Model

LD5HDCF-1

BB5HD-PG

LD5HDPG-1

LD5HDCPG-1

BB5HD-PG-E

LD5HDPG-E1

LD5HDCPG-E1

Spectra Lite and all Spectra II model dome drives are compatible with all Heavy-Duty back box models.

UNPACKING INSTRUCTIONS

If an item needs to be returned to the factory, consult the WARRANTY AND RETURN section of this manual for instructions.

The following items are supplied:

IN-CEILING MODELS

Back box

Mounting plate

Back mounting plates

Parts bag

8-32 x .275-inch screws

Conduit fitting

Safety chain bracket

Lock nut

Compass tool

PENDANT MODELS

Back box

Tube of thread compound

Pelco Installation Manual C2429M (3/01)

INSTALLATION IN-CEILING MODEL

STEP 1 - PREPARE CEILING

00530

00532

00531

a. Locate the center point of the mount-

ing location. Drill a hole in the ceiling

using a 3/32-inch drill.

b. Insert the compass tool into the hole.

c. Use the mounting ring as a template

and mark the hole pattern onto the

mounting surface. Prepare the holes.

Draw a circle on the ceiling using the

compass tool and a pencil. Cut the

circle out of the ceiling.

STEP 2 - INSTALL THE MOUNTING PLATES

Use the eight 10-32 x 3-inch screws (supplied) and install the mounting ring and

two back mounting plates.

CEILING

a. Line up the mount ring with the eight

fastener holes.

c. Install fasteners through the mount ring,

ceiling and out the back mounting plate.

b. Feed one back mounting plate through

the hole in the ceiling and line up with

four fastener holes.

d. Install second back mounting plate.

MOUNTING

RING

00533

STEP 3 - INSTALL THE BACK BOX

SPRING CLIP

ATTACH SAFETY CHAIN HERE

8-32X.275 INCH SCREW

00534

00535

00537

a. Attach the conduit fitting, lock nut, and

safety chain bracket. Install a safety

chain/cable (not supplied) that will

support up to 16 pounds (7.3 kg).

b. Turn the thumbscrew and open the

hinged door to the back box.Pull wiring

into the back box through the conduit

fitting. Refer to Tables A and B in the

Appendix for wiring distances.

c. Compress the spring clips on the back

box and push it through the hole, until

the clips spring back.Tighten the screws

until you hear a clicking noise. Insert the

two 8-32 x .275-inch screws to secure

the back box to the mount ring.

Pelco Installation Manual C2429M (3/01)

STEP 4 - WIRE CIRCUIT BOARD

24 VAC

TRANFORMER

POWER

(24 VAC ONLY)

Attach the wiring to the circuit board inside the back box. When

finished, close the door to the back box and turn on the power.

The red LED will light.

CONTROLLER

VIDEO IN

COAXITRON

CONTROLLER

VIDEO OUT

2 WIRE

CONTROLLER

TX-

TX+

RX-

RX+ CONTROL

TX-

IMPORTANT: If the LED does not light, refer to the Trouble-

shooting section.

NOT USED

(RS-422)

TX+

ALARM

INPUTS

NOTE: Aux 1 - Maximum 2A at low voltage (<40V)

SPECTRA II ONLY

Aux 2 - Maximum 150 vA at 32 VDC

GROUND

(NO)

(NC)

SWITCHES

(WIRING EXAMPLE)

+5 VDC

+5 to +24 VDC

RELAY

(AUX 1)

LOGIC GATE

(WIRING EXAMPLE)

AUX 2

GROUND

HEATER/FAN (NOT USED)

AUX 2

EXTERNAL RELAY

(WIRING EXAMPLE)

00542

STEP 5 - INSTALL DOME DRIVE

SW1

SW2

RED

TAB

GREEN

TAB

LABEL

SW1

SW2

LAB

SW2

RS-422 TERMINATION SWITCH

00539

00538

a. Set the DIP switches for SW1 and SW2 on the bottom of the

dome drive for the appropriate receiver address. Refer to the

labels on the dome drive orTables C through E in the Appendix

in the back of this manual.

b. Line up the green and red tabs with the green and red labels.

Push in on the tabs. Insert the side with the green tab, then the

side with red tab. Continue pushing on the ends of the tabs

until both sides click into place.

STEP 6 - INSTALL LOWER DOME

a. Attach the lower dome trim leash to one of the 8-32 x .275-

inch screws that secure the back box to the mounting ring.

b. Insert both keys in the barrel locks. Turn keys clockwise to the

unlocked position. Keys can not be removed from lock in the

unlocked position.

BALL STUD

RECEIVER

c. Align pegs (located on the mount ring) with the peg recep-

tacles (located on the inside of the lower dome).

TRIM LEASH

d. Place lower dome over back box. Hold and turn both keys to

the locked position.

TO USE YOUR DOME, REFER TO THE OPERATION AND

PROGRAMMING MANUAL.

BARREL

KEY LOCK

00497

Pelco Installation Manual C2429M (3/01)

INSTALLATION PENDANT MODELS

STEP 1 - MOUNT AND INSTALL THE BACK BOX

NOTE: If installing outdoors make sure the installation is properly sealed to keep moisture out.

00535

00540

a. Install the mount for the pendant dome. Refer to the instruc-

tions supplied with the mount. Bring the wiring for the dome

through the mount. Refer to Tables A and B in the Appendix for

wiring distances.

b. Turn the thumbscrew and open the hinged door located inside

the back box.

00541

c. Pull wiring from the mount into the back box.

d. Screw the back box into the mount. If outdoors, apply thread

compound (provided) to the threads on the back box.

24 VAC

TRANFORMER

POWER

(24 VAC ONLY)

CONTROLLER

VIDEO IN

COAXITRON

CONTROLLER

VIDEO OUT

STEP 2 - WIRE CIRCUIT BOARD

Attach the wiring to the interconnect circuit board inside the back

box. Close the door to the back box. Turn on power to the back

box. The red LED will light.

2 WIRE

CONTROLLER

TX-

TX+

RX-

RX+ CONTROL

TX-

NOT USED

(RS-422)

TX+

ALARM

INPUTS

SPECTRA II ONLY

IMPORTANT: If the LED does not light, refer to the Trouble-

shooting section.

GROUND

(NO)

(NC)

SWITCHES

(WIRING EXAMPLE)

+5 VDC

NOTE: Aux 1 - Maximum 2A at low voltage (<40V)

+5 to +24 VDC

RELAY

(AUX 1)

Aux 2 - Maximum 150 vA at 32 VDC

LOGIC GATE

(WIRING EXAMPLE)

AUX 2

GROUND

HEATER/FAN (NOT USED)

AUX 2

EXTERNAL RELAY

(WIRING EXAMPLE)

00542

Pelco Installation Manual C2429M (3/01)

STEP 3 - INSTALL DOME DRIVE

SW1

SW2

RED

TAB

GREEN

TAB

LABEL

SW1

SW2

LAB

SW2

RS-422 TERMINATION SWITCH

00539

00538

a. Set the DIP switches for SW1 and SW2 on the bottom of the

dome drive for the appropriate receiver address. Refer to the

labels on the dome drive or tables C through E in the Appendix

in the back of this manual.

b. Line up the green and red tabs with the green and red labels.

Push in on the tabs. Insert the side with the green tab, then the

side with red tab. Continue pushing on the ends of the tabs

until both sides click into place.

STEP 4 - INSTALL LOWER DOME

HEATER

CONNECTORS

BARREL

LOCK

TRIM

LEASH

O-RING

CENTER

00496

00543

a. Lightly apply O-ring lubricant to the O-ring. Install the O-ring in

the groove on the trim ring of the lower dome.

b. Align barrel locks in lower dome with the holes located on each

side of the back box. Push lower dome onto back box. Press

the pins of the barrel locks IN to secure the

lower dome.

Attach the back box trim leash to a retainer screw inside the

lower dome.

Environmental Model only: Plug the two-pin heater

connection in the lower dome into the mating connector in the

back box.

TO USE YOUR DOME, REFER TO THE OPERATION AND

PROGRAMMING MANUAL.

Pelco Installation Manual C2429M (3/01)

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

SOLUTION

Check to see if the red LED on the circuit

board in the back box is lit.

Unit does not operate.

The controller is not

communicating with

the Spectra unit.

1. The red LED is not lit.

a. Fuse is bad.

a. Check fuse on the circuit board. Replace fuse if it is

bad. To order a fuse from Pelco, specify the part

number FUS1.6-5X20FAST. This is a 1.6-ampere

fuse, 5 x 20 mm, fast blow.

b. Use a voltmeter to check if 24 VAC is getting to the

power connector on the circuit board. If NO, check

your power supply. If YES, return the back box to

the factory for repair.

b. 24 VAC power source is not con-

nected or back box is bad.

2. The red LED is lit.

a. Wiring is incorrect or is not fully

seated.

a. Check all connections to the circuit board.

Make sure that all connections are fully seated and

the board is wired correctly.

b. Check the DIP switch settings on the dome drive

(refer to Tables C, D, and E). If the unit still does

not operate, turn off power and replace the dome

drive with a good unit, if you have a spare. Check

the switch settings on the substitute dome drive

before installing it. (If you do not have a spare,

return the dome drive and back box to the factory.)

If you substituted a dome drive and the unit

operates, the original dome drive is bad (return

the dome drive to the factory). If the unit still

does not operate, then the circuit board is bad

(return the back box to the factory).

b. DIP switch settings are incorrect.

Make sure the connector for the fan is fully seated. If

the fan still does not operate, return the back box and

dome drive to the factory for repair.

Fan connections are not fully seated.

Cameras are out of phase.

Fan does not

operate.

If you are wiring more than one dome to the same

transformer, it is important to wire the power connec-

tor in each dome the same way. That is, the wiring

from one side of the transformer must be connected

to the same connector on each dome.

Vertical roll on monitor

when switching

between cameras.

WARNING: Make

DOME 1

POWER

sure you wire power

to the outer connec-

tors of the terminal

block and ground to

the middle connec-

tor. Otherwise, you

could damage the

dome.

DOME 2

POWER

DOME 3

POWER

00095

Pelco Installation Manual C2429M (3/01)

APPENDIX

Table A. Video Coaxial Cable Wiring Distances

Cable Type*

Maximum Distance

RG59/U

RG6/U

RG11/U

750 ft (229 m)

1,000 ft (305 m)

1,500 ft (457 m)

* Minimum cable requirements:

75 ohms impedance. All-copper center conductor.

95% braided copper shield.

Table B. 24 VAC Wiring Distances

The following are the recommended maximum distances for 24 VAC with a

10-percent voltage drop. (Ten percent is generally the maximum allowable

voltage drop for AC-powered devices.)

Wire Gauge

30 vA

75 vA

94 ft

(28 m)

150 ft

(45 m

238 ft

(115 m)

380 ft

(72 m)

603 ft

(183 m)

960 ft

(292 m)

37 ft

60 ft

95 ft

152 ft

241 ft

384 ft

(11 m)

(18 m)

(29 m)

(46 m)

(73 m)

(117 m)

NOTE: Input power for the dome is 24 VAC only. Power consumption is 30 vA

per dome for indoor models and 75 vA for outdoor models.

Use a 24 VAC transformer with the following minimum vA:

40 vA per dome

100 vA per dome

For indoor models (without heater)

For outdoor models (with heater)

Table C. Switch Settings for SW1

Control Type

Switch Setting

SW1-1

OFF

SW1-2

OFF

SW1-3

OFF

SW1-4

OFF

SW1-5

OFF

SW1-6

OFF

SW1-7

OFF

SW1-8

OFF**

Coaxitron^®

P-Type Control

D-Type Control

OFF

OFF*

NOTES: Switches SW 1-3 through SW 1-6 MUST be OFF.

D-type control is RS-422 that is compatible with Pelco’s CM6700, MPT9500, CM8500, and Genex^®controllers or with

American Dynamics control systems using the AD2083 Translator.

P-type control is RS-422 that is compatible with Pelco’s CM6700/CM9750/CM9760 and Genex control systems.

* OFF- Use with controllers that have more than 32 presets.

ON- Use with American Dynamics controllers (32 presets).

** OFF - Use with all control systems except CM9502 with variable speed keyboards.

For CM9502 with fixed speed keyboards, set switch OFF.

ON - Use with CM9502 with variable speed keyboards for smoother joystick control.

Pelco Installation Manual C2429M (3/01)

Table D. Switch Settings for SW2 – P-Type Control

NOTE: For Coaxitron controls, SW2 is not used; set all switches OFF. For D-type control systems, refer to Table E.

Receiver

Address

Switch Setting

SW2-3

Receiver

Address

Switch Setting

SW2-3

SW2-1

SW2-2

SW2-4

SW2-5

SW2-1

SW2-2

SW2-4

SW2-5

OFF

Baud Rate

Switch Setting

SW2-6

SW2-7

SW2-8

2400

4800

9600

OFF

Table E. Switch Settings for SW2 – D-Type Control

NOTE: For Coaxitron controls, SW2 is not used; set all switches OFF. For P-type control systems, refer to Table D.

Receiver

Address

Switch Setting

Receiver

Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

OFF

(Continued on next page)

Pelco Installation Manual C2429M (3/01)

Table E. Switch Settings for SW2 – D-Type Control (continued)

Receiver

Address

Switch Setting

Receiver

Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

OFF

100

101

102

103

104

OFF

(Continued on next page)

Pelco Installation Manual C2429M (3/01)

Table E. Switch Settings for SW2 – D-Type Control (continued)

Receiver

Address

Switch Setting

Receiver

Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

OFF

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

OFF

Pelco Installation Manual C2429M (3/01)

SPECIFICATIONS

MECHANICAL

Construction

Back box:

Aluminum

Dome drive:

Lower dome:

Aluminum, ABS plastic

Acrylic

Cable Entry

In-Ceiling:

Pendant:

.75-inch (1.91 cm) conduit fitting

Through 1.5-inch (3.81 cm) NPT pendant mount

Pan Movement:

Vertical Tilt:

360° continuous pan rotation

Unobstructed +2° to -92°

Manual Pan/Tilt Speeds*

Pan

Spectra II:

Spectra Lite:

Tilt

0.1-80°/sec manual operation, 150°/sec turbo

0.5-80°/sec manual operation, 150°/sec turbo

Spectra II:

Spectra Lite:

0.1-40°/sec

0.5-40°/sec

Preset Speeds

Pan:

Tilt:

250°/sec

200°/sec

* For variable-speed operation an appropriate controller is required. With fixed-speed controllers, Spectra II and Spectra Lite pan/tilt

speed is 24°/sec. The CM6700 controller with the KBD200 keyboard has programmable fixed speeds.

ELECTRICAL

Input Voltage:

18-30 VAC, 24 VAC nominal

Input Power

In-ceiling:

Indoor pendant:

Outdoor pendant:

30 vA

75 vA

Fuse:

1.6 A

Relay Contacts

Type:

AUX 1

Form C

AUX 2 Output

Open collector transistor output

Voltage:

Current:

Low voltage (<40 V) 32 VDC maximum

2 A maximum 150 mA maximum

Pelco Installation Manual C2429M (3/01)

GENERAL

Environment

In-Ceiling:

Pendant:

Indoor only

Indoor/outdoor

Operating Range

In-Ceiling:

32 to 140°F (0 to 60°C) intermittent operation; 32 to 122°F (0 to 50°C) continuous operation

Pendant

Without Heater:

32 to 140°F (0 to 60°C) absolute maximum operating temperature; 32 to 122°F (0 to 50°C) sustained

maximum operating temperature

With Heater:

(Assumes no wind chill factor; for detailed test conditions, contact Pelco.)

Maximum operating temperature: 140°F (60°C) absolute maximum; 122°F (50°C) sustained maximum

Minimum operating temperature: -60°F (-51.11°C) absolute minimum; minimal icing at -50°F (-45.56°C)

sustained minimum; prevents icing at -40°F (-40°C) sustained minimum; de-ices .1 inch (2.5 mm) within

3 hours after power-up

Dimensions:

Ratings:

See Figure 1

NEMA Type 1–In-ceiling back boxes, all dome drives

NEMA Type 4X–Pendant back boxes

IP 66–Pendant back boxes

Weight

Unit

Back Box

In-ceiling:

2.17 lb (.98 kg)

4.45 lb (2.02 kg)

4.75 lb (2.15 kg)

2.6 lb (1.18 kg)

Pendant Indoor:

Outdoor Pendant:

Dome Drive:

Lower Dome

In-ceiling:

In-ceiling w/cage:

Pendant:

Pendant w/cage:

1.6 lb (.73 kg)

1.83 lb (.83 kg)

(Design and product specifications subject to change without notice.)

.060

.125

10.1

(25.65)

7.5

(19.05)

ﬂ

6.13

15.57)

9.70

(24.64)

(

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;

ALL OTHERS ARE INCHES

Figure 1. Dimension Drawing

Pelco Installation Manual C2429M (3/01)

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or

workmanship for a period of one year after the date of shipment.

warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or

(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following

information:

1. Model and serial number

Exceptions to this warranty are as noted below:

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

•

Five years on FT/FR8000 Series ﬁber optic products.

Three years on Genex^®Series products (multiplexers, server, and keyboard).

If there is a dispute regarding the warranty of a product which does not fall under the

warranty conditions stated above, please include a written explanation with the product

when returned.

Three years on Camclosure^®and ﬁxed camera models, except the CC3701H-2,

CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,

which have a ﬁve-year warranty.

Method of return shipment shall be the same or equal to the method by which the item was

received by Pelco.

•

Two years on standard motorized or ﬁxed focal length lenses.

Two years on Legacy^®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

ﬁxed dome products.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at

(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned

for credit, and RA number if returned for repair).

•

Two years on Spectra^®, Esprit^®, ExSite^™, and PS20 scanners, including when used in

continuous motion applications.

•

Two years on Esprit^®and WW5700 Series window wiper (excluding wiper blades).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing

charge.

Eighteen months on DX Series digital video recorders, NVR300 Series network video

recorders, and Endura^™Series distributed network-based video products.

Goods returned for repair or credit should be clearly identiﬁed with the assigned CA or RA

number and freight should be prepaid. Ship to the appropriate address below.

•

One year (except video heads) on video cassette recorders (VCRs). Video heads will be

covered for a period of six months.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Six months on all pan and tilts, scanners or preset lenses used in continuous motion

applications (that is, preset scan, tour and auto scan modes).

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco

shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,

California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident

are not covered under this warranty.

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are

instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from

the speciﬁc use or application made of the Products. Pelco’s liability for any claim, whether

based on breach of contract, negligence, infringement of any rights of any party or product

liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for

such Products. In no event will Pelco be liable for any special, incidental or consequential

damages (including loss of use, loss of proﬁt and claims of third parties) however caused,

whether by the negligence of Pelco or otherwise.

Pelco

3500 Pelco Way

Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors

473 Eccles Avenue

The above warranty provides the Dealer with speciﬁc legal rights. The Dealer may also have

additional rights, which are subject to variation from state to state.

South San Francisco, CA 94080 USA

Phone: 650-737-1700

Fax: 650-737-0933

Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.

Endura and ExSite are trademarks of Pelco.

Loctite is a registered trademark of Loctite Corporation.

U.S. Patent No. 5,931,432.

REVISION HISTORY

Manual # Date Comments

C2429M

3/01

Original version.

Pelco Installation Manual C2429M (3/01)

Pelco Security Camera C1498M A User Manual
Philips Projector Garbo Series User Manual
Plantronics Headphones Voyager 855 User Manual
Playskool Games 50502 User Manual
PLH Products Swimming Pool SD 7103GC PEQ User Manual
Polycom Telephone Accessories EF2280 User Manual
Precisionaire Air Cleaner KKM User Manual
Presto Electric Pressure Cooker Electric Pressure Washer User Manual
ProForm Treadmill 831297000 User Manual
PSB Speakers Portable Speaker Loudspeakers User Manual